Description
Original lint filter gasket for Bosch tumble dryer | Bosch 00656034
The original filter seal prevents air leaks and ensures efficient and fast drying. This is an original BSH part suitable for Bosch heat pump tumble dryers. Before ordering, click the 'Check Model Compatibility' button at the top of the page and make sure it is fully compatible with your appliance.
⚠️ Just before ordering – safety above all!
To ensure a successful repair and maintain the life of your dryer, it is essential to use only genuine parts . Non-genuine seals may cause air leaks, reduce drying efficiency, and void the warranty. Now click the 'Check Model Compatibility' button above and the system will immediately confirm that the part is suitable for you.
What is the function of the lint filter gasket?
The Fluff Filter Seal creates a hermetic seal around the lint filter at the dryer inlet. It prevents air from bypassing the filter and ensures that all airflow passes through the filter as required.
In our experience at official service laboratories , a worn or damaged gasket is one of the common causes of the following drying problems:
✅ Longer than usual drying times – The hot air escapes and does not dry effectively.
✅ Lint buildup around the door – A clear sign of an air leak
✅ Excessive humidity in the room – The humid air is not routed properly
✅ High power consumption – The dryer works harder to achieve results
✅ Moisture at the bottom of the device – Improper condensation
When should the gasket be replaced?
Our certified technicians indicate that the gasket should be replaced when:
- The gasket is torn, cracked, or deformed.
- The gasket has hardened and lost its elasticity.
- There are visible gaps between the gasket and the filter.
- The laundry comes out damp even after a full drying cycle.
- Lint builds up around the door or inside the dryer
Why an original gasket?
Using an original BSH gasket ensures:
- perfect match For filter dimensions without gaps
- Optimal flexibility For long-term hermetic sealing
- Heat resistance – Adapted to the dryer's operating temperatures
- Maintaining responsibility of the device
- Energy efficiency – Preventing electricity waste
Non-genuine gaskets may shrink in heat, harden too quickly, and not provide adequate sealing.
Where do you find the model number?
The Bosch tumble dryer model sticker is usually located on the inside of the door opening or on the inside of the door . Look for a sticker with a model number that starts with WQG, WTG, WTW or similar.
Technical
| attribute | value |
|---|---|
| Manufacturer's SKU: | 00656034 |
| Manufacturer: | BSH (Bosch / Siemens) |
| Part type: | Fluff Filter Seal |
| material: | Flexible rubber/silicone |
| Colour: | black |
| Location on device: | Around the lint filter in the door opening |
| compatibility: | Condenser/heat pump tumble dryers |
| Compatible models: | WQG2419IL and other models from the WQG, WTG, WTW, WTR series |
| installation: | Self-contained – simple replacement without tools |
🔧 Installation instructions
The replacement is simple and takes just a few minutes:
- Unplug the dryer. – Safety comes first.
- Remove the lint filter. From its opening
- Remove the old gasket. – Gently pull it out of the frame
- Clean the surface. – Remove any lint and dirt residue.
- Install the new gasket. – Make sure it sits securely around the entire circumference
- Put the filter back in place. And check that the door closes properly.
Expert tip: Before installing the new gasket, thoroughly clean the filter area and check for lint buildup in the vents.
🛡️ Preventive maintenance tip
To extend the life of the seal and dryer:
- Clean the lint filter. After each drying cycle
- Clean the heat exchanger. Once a month
- Check the gasket. Once every six months For early crack detection
- Do not load the dryer beyond ⅔ of its capacity.
FAQ
Q: Does the gasket fit my model?
A: Click the 'Check Model Compatibility' button at the top of the page for instant verification.
Q: Is this an original product?
A: Yes. This is an original part from BSH, the manufacturer of the Bosch and Siemens brands.
Q: How often is it recommended to replace the gasket?
A: The gasket is designed for extended use of several years. Replace only when there are signs of wear such as tears, hardening, or air leaks.
Q: Can I install it myself?
A: Absolutely. Installation is simple and does not require special tools or a technician.
Q: How do I know if the gasket is damaged?
A: Clear signs: long drying times, lint accumulating around the door, moisture at the bottom of the dryer, or clothes coming out damp.
















